Methods To Punch A Hole In A Leather Belt

I'd like to introduce you to certainly one of my all time favorite fashion tools… the Leather Hole puncher ! Possibly you lost or gained some weight; possibly you found the right belt at a thrift store, nevertheless it's a not the appropriate measurement; possibly you need a Hole between two of the already current holes-whatever the challenge is, this tutorial will show you how to add nice spherical belt holes. Use a chunk of scrap Leather beneath the belt, so that you just're not hammering the punch proper into the anvil. The brand new holes look slightly extra ragged around the edges, however using the belt will assist to smooth them down.
It is best to be certain the unit is designed to line up accurately with the chopping plate because each reduce I needed to verify it by lining it up and looking at it with light behind it to see if it could hit flat and even then I did not get a superb reduce. The primary time I wanted additional holes for my belt I laid the belt on our eating table, took a steak knife, stabbed and began twisting the knife into the Leather as if I was making an attempt to make a boy scout fire with two sticks of wooden.



I heat the nail over the range, drive it with pliers, bend the belt on the opening and smoothen edges with sand paper. Sadly, in the event you put much pressure on it, the uneven Hole will allow the Leather to tear fairly easily. Lay the belt down on a flat floor, mistaken side up. Measure how far apart the pre-lower belt holes are so as to place the new belt holes correctly. For the sake of aesthetics, it is best to put in holes up to the point of the specified closure point.
Maybe you misplaced or gained some weight; maybe you found the right belt at a thrift retailer, however it's a not the right size; maybe you need a Hole between two of the already present holes-regardless of the difficulty is, this tutorial will present you the way to add good round belt holes. Use a chunk of scrap Leather beneath the belt, so that you just're not hammering the punch right into the anvil. The new holes look barely more ragged across the edges, however using the belt will assist to smooth them down.

A nail will make a smoother Hole by a thin belt, but should you're trying to save time, a screw might be turned by the Leather, using its threads to tear by way of quicker. I had to use scissors to scrub every Hole up and it took a LOT of strain simply to get that! I could possibly be okay if all you wish to do is make a new Hole in a belt but............you get what you pay for. Even fresh out of the box, this set of pliers has a lot of play in its alignment - very easy to not get on the anvil square and punch an ovular Hole. I wanted a belt that was a little longer, and so I went with a forty five″ in. size and a 1″ in. width.
Mark out the place you need the brand new Hole, and put the knife on the marker and rotate gently. Once, it manages to pierce to the other end, start rotating it, while concurrently drilling in; till the hole of desired dimension(or diameter) is punched in. To maintain the belt consistant you're going to need to measure out the exsisting holes. In my case they had been an inch appart, so I measured an inch from the last Hole and made a mark with the sharpie. To create the opening take the nail and place it on the mark you made, then take the your scrap piece of wooden to hammer the nail by the belt.
I used to be looking at the website and it appeared like the three/four″ large belt is $12.99, the 1.5″ belt blank is $19.99. I suppose you would lower your expenses by signing up for his or her membership prices, however this nonetheless places the belt in at $30, which remains to be an amazing deal. Tony, A Leather punch will provide you with a extra consistent Hole, but in the event you're solely making one belt, I would not spend the extra cash for the punch.

In case your high precedence is a snug match, instead wear the belt and pull it to a snug position, then mark the belt the place the strap tongue touches it. Use heavy objects to overwhelm every end of the belt, with the location where the opening will probably punch hole in belt be punched on prime of a block of wooden or other onerous, flat surface. You may as well decide to snipping the other end, as soon as it has penetrated the outer layer a bit, as a substitute of drilling a perfect Hole.
Work slowly and thoroughly-this top sew will preserve your belt collectively, but it can additionally look beautifully decorated if it's executed nicely! Start on the bottom corner of the tail end (where you possibly can see I left the threads on the left side), go down the end, and then pivot at the nook to turn and continue all the best way down the size of your belt. It should not take much thread, however be extra cautious when you're working with a thicker material.

Leave a Reply

Your email address will not be published. Required fields are marked *